Gamer.Site Web Search

  1. Ad

    related to: 1.5 od pipe dimensions in cm

Search results

  1. Results From The WOW.Com Content Network
  2. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  3. British Standard Pipe - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Pipe

    British Standard Pipe ( BSP) is a set of technical standards for screw threads that has been adopted internationally for interconnecting and sealing pipes and fittings by mating an external ( male) thread with an internal (female) thread. It has been adopted as standard in plumbing and pipe fitting, except in North America, where NPT and ...

  4. Iron pipe size - Wikipedia

    en.wikipedia.org/wiki/Iron_pipe_size

    Iron Pipe Size (IPS or I.P.S.) pipe sizing system based on the inside diameter (ID) of pipe. It was widely used from the early 19th century to the mid 20th century and is still in use by some industries, including major PVC pipe manufacturers, as well as for some legacy drawings and equipment. The iron pipe size standard came into being early ...

  5. Piping and plumbing fitting - Wikipedia

    en.wikipedia.org/wiki/Piping_and_plumbing_fitting

    Pipe fittings: 1) Copper (solder); 2) Iron or brass (threaded); 3) Brass (compression); 4) Brass (compression to solder); 5) Brass adapters. PVC fittings. A fitting or adapter is used in pipe systems to connect sections of pipe (designated by nominal size, with greater tolerances of variance) or tube (designated by actual size, with lower ...

  6. National pipe thread - Wikipedia

    en.wikipedia.org/wiki/National_pipe_thread

    National pipe taper fuel (NPTF) National Pipe Taper Fuel ( NPTF, also called Dryseal American National Standard Taper Pipe Thread, defined by ASME B1.20.3) is designed to provide a more leak-free seal without the use of PTFE tape (often referred to by the popular brand name "Teflon") or another sealant compound.

  7. List of battery sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_battery_sizes

    3LR12 (4.5-volt), D, C, AA, AAA, AAAA (1.5-volt), A23 (12-volt), PP3 (9-volt), CR2032 (3-volt), and LR44 (1.5-volt) batteries. This is a list of the sizes, shapes, and general characteristics of some common primary and secondary battery types in household, automotive and light industrial use. The complete nomenclature for a battery specifies ...

  8. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

  9. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  1. Ad

    related to: 1.5 od pipe dimensions in cm